Monthly Student Online Competition

Electronics and Circuits MCQs with Answers

Electronics and Circuits MCQs

Welcome to the Electronics and Circuits MCQs with Answers. In this post, we are sharing Electronics and Circuits Multiple Choice Questions and Answers in Everyday Science section for various competitive exams in Pakistan. Each question offers a chance to enhance your knowledge regarding Electronics and Circuits online MCQs Test.

What is the fundamental unit of information in digital electronics?
a) Bit
b) Byte
c) Volt
d) Ampere

Answer
a) Bit

Which of the following components is used to amplify electrical signals?
a) Resistor
b) Capacitor
c) Diode
d) Transistor

Answer
d) Transistor

What does the acronym “AC” stand for in AC circuits?
a) Alternating Current
b) Ampere Circuit
c) Analog Capacitance
d) Automated Control

Answer
a) Alternating Current

What is the most basic function of an operational amplifier (op-amp)?
a) Addition
b) Subtraction
c) Amplification
d) Differentiation

Answer
c) Amplification

What does the acronym “LED” stand for in electronics?
a) Light Emitting Device
b) Low Energy Diode
c) Long-lasting Electronic Display
d) Light Emitting Diode

Answer
d) Light Emitting Diode

What is the purpose of a capacitor in an electronic circuit?
a) To store electrical energy
b) To control current flow
c) To amplify signals
d) To rectify AC voltage

Answer
a) To store electrical energy

What is the basic unit of resistance?
a) Volt
b) Ampere
c) Ohm
d) Farad

Answer
c) Ohm

Which type of circuit allows current to flow in only one direction?
a) Open circuit
b) Closed circuit
c) AC circuit
d) DC circuit

Answer
d) DC circuit

What is the purpose of a diode in a circuit?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To measure voltage

Answer
b) To control current flow

What is the relationship between voltage, current, and resistance in a circuit?
a) V = IR
b) V = I/R
c) I = RV
d) R = VI

Answer
a) V = IR

What does the acronym “AC/DC” stand for in relation to electrical power?
a) Alternating Current/Direct Current
b) Ampere Control/Diode Circuit
c) Analog Capacitance/Digital Control
d) Automated Control/Diode Circuit

Answer
a) Alternating Current/Direct Current

Which component is used to protect other components from excessive current flow in a circuit?
a) Capacitor
b) Transistor
c) Resistor
d) Fuse

Answer
d) Fuse

What is the purpose of a resistor in a circuit?
a) To store electrical energy
b) To control current flow
c) To amplify signals
d) To rectify AC voltage

Answer
b) To control current flow

What is the function of a transistor in an electronic circuit?
a) To amplify signals
b) To store electrical energy
c) To rectify AC voltage
d) To measure voltage

Answer
a) To amplify signals

What is the relationship between power, voltage, and current in a circuit?
a) P = IV
b) P = I/V
c) P = VI
d) P = V/I

Answer
c) P = VI

What does the acronym “IC” stand for in electronics?
a) Integrated Circuit
b) Insulated Capacitor
c) Inductive Coil
d) Integrated Capacitance

Answer
a) Integrated Circuit

What is the purpose of a transformer in an electrical circuit?
a) To control current flow
b) To store electrical energy
c) To amplify signals
d) To change voltage levels

Answer
d) To change voltage levels

What is the function of a logic gate in digital electronics?
a) To amplify signals
b) To store electrical energy
c) To control current flow
d) To perform Boolean operations

Answer
d) To perform Boolean operations

What is the basic unit of capacitance?
a) Volt
b) Ampere
c) Ohm
d) Farad

Answer
d) Farad

What is the purpose of a voltage regulator in a circuit?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To maintain a constant voltage

Answer
d) To maintain a constant voltage

What does the term “ground” refer to in an electrical circuit?
a) The positive terminal of a power supply
b) The negative terminal of a power supply
c) The point of reference for voltage measurements
d) The path through which current flows

Answer
c) The point of reference for voltage measurements

What is the purpose of an inductor in an electronic circuit?
a) To amplify signals
b) To store electrical energy
c) To control current flow
d) To rectify AC voltage

Answer
c) To control current flow

What is the function of a multimeter in electronics?
a) To measure voltage, current, and resistance
b) To amplify signals
c) To control current flow
d) To store electrical energy

Answer
a) To measure voltage, current, and resistance

What does the term “digital” refer to in electronics?
a) Continuous signal representation
b) Analog circuit design
c) Binary signal representation
d) Electrical energy storage

Answer
c) Binary signal representation

What is the purpose of a relay in an electrical circuit?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To rectify AC voltage

Answer
b) To control current flow

Which component is used to measure the flow of electric current in a circuit?
a) Resistor
b) Capacitor
c) Ammeter
d) Voltmeter

Answer
c) Ammeter

What is the purpose of a Zener diode in a circuit?
a) To control current flow
b) To amplify signals
c) To store electrical energy
d) To regulate voltage

Answer
d) To regulate voltage

What does the term “analog” refer to in electronics?
a) Continuous signal representation
b) Binary signal representation
c) Digital circuit design
d) Electrical energy storage

Answer
a) Continuous signal representation

What is the function of a NAND gate in digital electronics?
a) AND operation followed by NOT operation
b) OR operation followed by NOT operation
c) XOR operation followed by NOT operation
d) NOT operation followed by OR operation

Answer
a) AND operation followed by NOT operation

What is the purpose of a thyristor in an electronic circuit?
a) To control current flow
b) To amplify signals
c) To store electrical energy
d) To measure voltage

Answer
a) To control current flow

What is the purpose of a voltage divider in a circuit?
a) To control current flow
b) To store electrical energy
c) To amplify signals
d) To divide voltage levels

Answer
d) To divide voltage levels

What does the term “logic level” refer to in digital electronics?
a) The voltage level used to represent binary values
b) The maximum voltage a circuit can handle
c) The minimum voltage required for circuit operation
d) The level of complexity in a logic circuit

Answer
a) The voltage level used to represent binary values

What is the purpose of a motor driver in an electronic circuit?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To measure voltage

Answer
b) To control current flow

What is the function of a NOR gate in digital electronics?
a) OR operation followed by NOT operation
b) AND operation followed by NOT operation
c) XOR operation followed by NOT operation
d) NOT operation followed by OR operation

Answer
a) OR operation followed by NOT operation

What does the term “transconductance” refer to in electronics?
a) The ability of a device to amplify signals
b) The flow of electric current in a circuit
c) The change in voltage with respect to current
d) The conversion of electrical energy into mechanical energy

Answer
c) The change in voltage with respect to current

What is the purpose of a logic probe in electronics?
a) To measure voltage, current, and resistance
b) To amplify signals
c) To control current flow
d) To test logic states in a circuit

Answer
d) To test logic states in a circuit

What does the term “inverting” refer to in relation to op-amps?
a) The input and output voltages have opposite polarities
b) The input and output voltages have the same polarity
c) The input voltage is negative and the output voltage is positive
d) The input voltage is positive and the output voltage is negative

Answer
a) The input and output voltages have opposite polarities

What is the purpose of a digital-to-analog converter (DAC) in electronics?
a) To amplify signals
b) To control current flow
c) To convert digital signals to analog signals
d) To convert analog signals to digital signals

Answer
c) To convert digital signals to analog signals

What does the term “feedback” refer to in electronics?
a) The process of transferring signals between different circuits
b) The process of providing an output signal to the input of a circuit
c) The process of controlling current flow in a circuit
d) The process of storing electrical energy in a circuit

Answer
b) The process of providing an output signal to the input of a circuit

What is the purpose of a decoupling capacitor in a circuit?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To stabilize voltage levels

Answer
d) To stabilize voltage levels

What does the term “frequency” refer to in electronics?
a) The number of cycles per second in an alternating current
b) The rate at which electrons flow in a circuit
c) The amount of charge passing through a circuit per unit time
d) The energy carried by an electric field per unit charge

Answer
a) The number of cycles per second in an alternating current

What is the function of a Schmitt trigger in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To convert analog signals to digital signals

Answer
d) To convert analog signals to digital signals

What does the term “gate” refer to in digital electronics?
a) A device used to control current flow in a circuit
b) A logic circuit that performs a specific function
c) The opening through which electrons flow in a semiconductor
d) The input and output terminals of an electronic component

Answer
b) A logic circuit that performs a specific function

What is the purpose of a flip-flop in digital electronics?
a) To amplify signals
b) To control current flow
c) To store and manipulate binary information
d) To convert analog signals to digital signals

Answer
c) To store and manipulate binary information

What does the term “bit rate” refer to in digital communications?
a) The number of bits transmitted per unit time
b) The voltage level used to represent binary values
c) The time it takes for a signal to propagate through a circuit
d) The rate at which electrons flow in a circuit

Answer
a) The number of bits transmitted per unit time

What is the function of a voltage follower in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To provide a high-input impedance and low-output impedance

Answer
d) To provide a high-input impedance and low-output impedance

What does the term “gate leakage current” refer to in electronics?
a) The current flowing through a logic gate
b) The current flowing through a power supply
c) The current leaking through the insulation of a MOSFET
d) The current flowing through a diode

Answer
c) The current leaking through the insulation of a MOSFET

What is the purpose of a phase-locked loop (PLL) in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To synchronize signals

Answer
d) To synchronize signals

What does the term “resonance” refer to in electronics?
a) The phenomenon when the natural frequency of a system matches the applied frequency
b) The process of amplifying electrical signals
c) The phenomenon when voltage and current are in phase in an AC circuit
d) The process of converting analog signals to digital signals

Answer
a) The phenomenon when the natural frequency of a system matches the applied frequency

What is the purpose of a voltage-controlled oscillator (VCO) in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To generate a frequency that is proportional to an input voltage

Answer
d) To generate a frequency that is proportional to an input voltage

What does the term “hysteresis” refer to in electronics?
a) The lag in response time of a circuit
b) The difference between the input and output voltages of an op-amp
c) The voltage level at which a Schmitt trigger changes state
d) The process of converting analog signals to digital signals

Answer
c) The voltage level at which a Schmitt trigger changes state

What is the purpose of a voltage-to-frequency converter in electronics?
a) To amplify signals
b) To control current flow
c) To convert voltage levels to frequency signals
d) To generate a square wave signal

Answer
c) To convert voltage levels to frequency signals

What does the term “transistor biasing” refer to in electronics?
a) The process of amplifying signals using transistors
b) The process of controlling current flow in transistors
c) The process of storing electrical energy in transistors
d) The process of converting analog signals to digital signals using transistors

Answer
b) The process of controlling current flow in transistors

What is the purpose of a current mirror in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To measure voltage

Answer
b) To control current flow

What does the term “Miller effect” refer to in electronics?
a) The phenomenon of capacitance multiplication in a common-emitter amplifier
b) The process of amplifying electrical signals
c) The phenomenon of energy transfer between inductors
d) The process of converting analog signals to digital signals

Answer
a) The phenomenon of capacitance multiplication in a common-emitter amplifier

What is the function of a voltage comparator in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To compare two input voltages and provide a digital output

Answer
d) To compare two input voltages and provide a digital output

What does the term “current gain” refer to in relation to transistors?
a) The ratio of output current to input current in a transistor
b) The ratio of output voltage to input voltage in a transistor
c) The ability of a transistor to amplify signals
d) The process of converting analog signals to digital signals using transistors

Answer
a) The ratio of output current to input current in a transistor

What is the purpose of a voltage stabilizer in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To maintain a constant output voltage

Answer
d) To maintain a constant output voltage

What does the term “gain bandwidth product” refer to in electronics?
a) The product of voltage gain and current gain of an amplifier
b) The range of frequencies over which an amplifier can provide gain
c) The ability of an amplifier to amplify signals
d) The process of converting analog signals to digital signals using amplifiers

Answer
b) The range of frequencies over which an amplifier can provide gain

What is the function of a current sense resistor in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To measure the current flowing through a circuit

Answer
d) To measure the current flowing through a circuit

What does the term “common mode rejection ratio” (CMRR) refer to in electronics?
a) The ability of an amplifier to reject common-mode signals
b) The ratio of output voltage to input voltage in an amplifier
c) The process of amplifying electrical signals
d) The ability of a circuit to generate accurate voltage levels

Answer
a) The ability of an amplifier to reject common-mode signals

What is the purpose of a bandpass filter in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To allow only a specific range of frequencies to pass through

Answer
d) To allow only a specific range of frequencies to pass through

What does the term “op-amp saturation” refer to in electronics?
a) The condition when the output voltage of an op-amp reaches its maximum or minimum value
b) The process of amplifying electrical signals
c) The process of converting analog signals to digital signals using op-amps
d) The condition when the input voltage of an op-amp exceeds its supply voltage

Answer
a) The condition when the output voltage of an op-amp reaches its maximum or minimum value

What is the function of a digital encoder in electronics?
a) To amplify signals
b) To control current flow
c) To convert analog signals to digital signals
d) To convert digital signals to analog signals

Answer
c) To convert analog signals to digital signals

What does the term “charge pump” refer to in electronics?
a) A circuit that generates a high voltage from a low voltage source
b) The process of amplifying electrical signals
c) The process of converting analog signals to digital signals
d) A circuit that generates a DC voltage by pumping charge from one node to another

Answer
d) A circuit that generates a DC voltage by pumping charge from one node to another

What is the purpose of a power amplifier in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To provide high-power output signals

Answer
d) To provide high-power output signals

What does the term “frequency response” refer to in electronics?
a) The range of frequencies over which a circuit can provide gain
b) The process of amplifying electrical signals
c) The phenomenon of energy transfer between inductors
d) The process of converting analog signals to digital signals using amplifiers

Answer
a) The range of frequencies over which a circuit can provide gain

What is the function of a digital decoder in electronics?
a) To amplify signals
b) To control current flow
c) To convert digital signals to analog signals
d) To convert digital signals to discrete outputs

Answer
d) To convert digital signals to discrete outputs

What does the term “feedback loop” refer to in electronics?
a) The process of transferring signals between different circuits
b) The process of providing an output signal to the input of a circuit
c) The process of controlling current flow in a circuit
d) The process of storing electrical energy in a circuit

Answer
b) The process of providing an output signal to the input of a circuit

What is the purpose of a voltage-controlled resistor in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To vary the resistance based on an input voltage

Answer
d) To vary the resistance based on an input voltage

What does the term “linearity” refer to in electronics?
a) The ability of a circuit to provide a linear relationship between input and output signals
b) The process of amplifying electrical signals
c) The process of converting analog signals to digital signals using amplifiers
d) The ability of a circuit to provide consistent gain over a wide frequency range

Answer
a) The ability of a circuit to provide a linear relationship between input and output signals

What is the function of a digital counter in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To count digital events

Answer
d) To count digital events

What does the term “common collector” refer to in relation to transistor configurations?
a) A transistor configuration where the collector terminal is connected to a common point
b) A transistor configuration where the base terminal is connected to a common point
c) A transistor configuration where the emitter terminal is connected to a common point
d) A transistor configuration where the collector and emitter terminals are connected to a common point

Answer
a) A transistor configuration where the collector terminal is connected to a common point

What is the purpose of a digital multiplexer in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To select one of several input signals and route it to an output

Answer
d) To select one of several input signals and route it to an output

What does the term “pull-up resistor” refer to in electronics?
a) A resistor connected between the input and output of a circuit
b) A resistor connected between the power supply and an input terminal
c) A resistor connected between the power supply and an output terminal
d) A resistor connected between the ground and an output terminal

Answer
c) A resistor connected between the power supply and an output terminal

What is the function of a voltage-to-current converter in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To convert voltage signals to current signals

Answer
d) To convert voltage signals to current signals

What does the term “dead time” refer to in electronics?
a) The time delay between the activation and deactivation of a circuit
b) The process of amplifying electrical signals
c) The process of converting analog signals to digital signals using amplifiers
d) The time interval during which a circuit is non-responsive

Answer
a) The time delay between the activation and deactivation of a circuit

What is the purpose of a current-controlled resistor in electronics?
a) To amplify signals
b) To control current flow
c) To store electrical energy
d) To vary the resistance based on an input current

Answer
d) To vary the resistance based on an input current

What does the term “ringing” refer to in electronics?
a) The oscillation or overshoot that occurs in a circuit’s response to a step input
b) The process of amplifying electrical signals
c) The phenomenon of energy transfer between inductors
d) The process of converting analog signals to digital signals using amplifiers

Answer
a) The oscillation or overshoot that occurs in a circuit’s response to a step input

If you are interested to enhance your knowledge regarding PhysicsChemistryComputer, and Biology please click on the link of each category, you will be redirected to dedicated website for each category.

See Also  Elements, Compounds, and Mixtures MCQs with Answers
Was this article helpful?
YesNo
Facebook
Twitter
LinkedIn
WhatsApp
Pinterest
Telegram
Picture of YFP

YFP

YFP empower the youth with the ability to nurture their communication and leadership skills at a common national platform resulting in greater self-confidence and personal growth.

Leave a Reply

Your email address will not be published. Required fields are marked *